Sustainable urban sewage treatment plant using renewable energy

Introduction

If you specify or buy polyethylene pipe, “PE80” and “PE100” are two of the first numbers you’ll meet. They look like a small difference. In practice, they decide how thick your pipe wall has to be, how much pressure the line can carry, and how much material you pay for over the life of a network. Here’s what the numbers mean and how to choose.

What the numbers actually mean

The figure after “PE” is the material’s Minimum Required Strength (MRS) in megapascals: the stress the polyethylene can safely withstand over a 50-year design life at 20°C.

  • PE80 has an MRS of 8.0 MPa.
  • PE100 has an MRS of 10.0 MPa.

That 25% jump in strength drives everything else. A stronger material lets you do one of two things: use a thinner wall for the same pressure, or carry more pressure with the same wall.

Quick answer

PE100 is stronger than PE80, so for the same pressure rating it needs a thinner wall. That means a larger internal bore, higher flow capacity, and less material per metre. For most modern water, gas, and sewerage projects, PE100 is the default choice. PE80 still appears in smaller-diameter and some gas applications where legacy specifications or lower pressures apply.

How it plays out in the pipe wall

Pipe pressure rating comes from the ratio of diameter to wall thickness, expressed as SDR (Standard Dimension Ratio). The design equation is:

P = 2 × σ / (SDR - 1)

where σ is the design stress (MRS divided by a safety factor). Because PE100 starts from a higher MRS, its design stress is higher, at 8.0 MPa versus 6.3 MPa for PE80 under the standard water safety factor. The result, for any given pressure class, looks like this:

PE80 PE100
MRS 8.0 MPa 10.0 MPa
Design stress (water) 6.3 MPa 8.0 MPa
Wall for the same PN Thicker Thinner
Internal bore (same OD) Smaller Larger
Flow capacity (same OD) Lower Higher

So at the same outside diameter and the same pressure class, a PE100 pipe gives you a bigger internal bore and moves more water. Holding the bore constant instead, PE100 lets you step up to a higher pressure class.

Why most specifiers have moved to PE100

Three practical reasons stand out:

  1. Material efficiency. Thinner walls mean less polyethylene per metre. On a long transmission main, that adds up to real savings in material and transport weight.
  2. Hydraulic performance. The larger bore reduces friction losses, which can let you specify a smaller nominal diameter for the same flow.
  3. Availability and standardisation. PE100 is now the industry baseline across European water and gas networks, which makes fittings, jointing, and supply straightforward.

When PE80 still makes sense

PE80 has not disappeared. It is still specified for some gas distribution networks, smaller service connections, and projects where an existing specification or asset standard calls for it. If you are extending or repairing a PE80 network, matching the existing material can be the right call. The key is to confirm the pressure class and SDR rather than assuming the grade alone tells you everything.

A note on PE100-RC

For demanding installation conditions such as trenchless laying, rocky backfill, or no sand bedding, there is a further grade, PE100-RC (“Resistance to Crack”), engineered to resist slow crack growth and point loading. It is a separate decision from the PE80 versus PE100 question, and worth understanding on its own.

FAQ

Is PE100 always better than PE80?
For new pressure networks, usually yes: it is more material-efficient and offers better flow. But “better” depends on the spec. If a project standard requires PE80, that is what you supply.

Can I mix PE80 and PE100 in one network?
You can join them, but you must design to the lower of the two ratings at the junction and use appropriate fittings. It is cleaner to standardise on one grade where possible.

Does PE100 cost more?
Per kilogram, grades are comparable. Per metre of finished pipe, PE100 often costs less for the same pressure rating because it uses a thinner wall.

Konti Hidroplast manufactures PE100 and PE80 pipes for water supply, gas, and sewerage across a full range of diameters and pressure classes, all to recognised European standards. Water supply · Contact us